$1,966.00

Weight Loaded 6" Pressure Relief Valve
[TS-WPRV-6]

Weight Loaded 6\" Pressure Relief Valve
Price includes valve weights for up to 5 PSI. If a different amount of weights are required, please contact us for a proposal.

Design Features

The weight loaded pressure relief valve offers inexpensive relief capacity in a sturdy, trouble free design in 1" though 8" sizes.

Sizes 1" through 4" have standard male threaded connections. Sizes 6" and 8' have standard 125# ANSI flange drillings.

Removable weights have been carefully designed to permit accurate pressure settings in 1/2 PSI increments in the 1 " through 4" size and 1/2 and 1 PSI increments in 6" and 8" size.

The operation of the relief valve is simple. As the service line air pressure reaches the pressure setting, the weight loaded cap is forced upwards off the valve seat. As pressure increases, the cap rises to expose the discharge ports. The flow-through capacity of the valve is such that no damage can be caused to the blower or related systems.

The valve automatically reseats itself as line pressure is reduced.

Since the opening and closing of the valve is essentially the sliding of a piston in a cylinder, the valve is virtually chatter-free. The body and cap of the valve are made of cast iron with close tolerance machined surfaces in the operating areas. The weights are cut from uniform steel plate or uniformly cast to give accurate pressure adjustment.

The weight loaded relief valve was engineered to provide long and dependable protection for your positive displacement blower and associated systems by its simplicity af design. Weight loaded pressure reliefs are designed to protect the blower against damage caused by operation at greater than designed pressure or vacuum. However, they are not intended as pressure regulators.

Maintenance

Application of light oil to the mating surfaces of the cap and body periodically is all the maintenance required on this valve.

Installation

For proper operation, the valve must be mounted in exact upright position. Use only full flange gasket.

General Dimensions for Flanged 125# ANSI - 6" and 8"



Valve Size A B C D
6 INCH 6 9-5/8 6-1/2 2-5/8
8 INCH 8 11-1/4 9-1/4 2-3/4
Note: A is Mounting Flange, ASA 125# Flange Drilling. Dimensions in Inches. Use only full flange gasket.



Note: Valves not recommended to relief at set pressures under 5 PSIG.

Specifications subject to change without notice.
We Accept
1 x End Plug Assembly
1 x Spring-Loaded 1-1/2" Pressure Relief Valve
1 x LP4775 33" Amalgam Ultraviolet Lamp, 3-1 Step
1 x QZ0285 35-1/2" Quartz Sleeve
1 x Compression Nut
1 x QZ0640 68" Quartz Sleeve
1 x QZ0115 14-7/8" Quartz Sleeve
1 x LP4420 33" HO Ultraviolet Lamp, 4 Pin Flat
1 x LP4155 6.75" Ultraviolet Lamp, 4 Pin Flat
1 x QZ0125 35-1/8" Quartz Sleeve
1 x 1-1/4" Series 7 US Valve - Check Valve
1 x LP4290 17" Ultraviolet Lamp, 4 Pin Flat
1 x LP4090 18" Ozone Ultraviolet Lamp, 4 Pin Flat
1 x LP4085 25.5" Ozone Ultraviolet Lamp, 4 Pin Flat
1 x LP4395 33.2" Ultraviolet Lamp, 3-1 Step
1 x LP4030 61.2" Ultraviolet Lamp, 2/2 Pin Step
1 x LP4185 22" Ultraviolet Lamp, 1 Pin Each End
1 x LP4260 18" Ultraviolet Lamp, 4 Pin Flat
1 x LP4055 33.2" Ozone Ultraviolet Lamp, 4 Pin Flat
1 x LP4695 31.88" Ultraviolet Lamp, 3-1 Step
1 x O-Ring for Sunlight Systems SL160
1 x Spring-Loaded 2" Pressure Relief Valve
1 x 1.5" Rubber Hose Connection
1 x LP4165 14" Ultraviolet Lamp, 1 Pin Each End
1 x Norweco AT1500 UV Quartz Sleeve with Teflon Coating
1 x Solberg Small Filter Silencer 2" NPT(M) - FS-30P-200
1 x O-Ring for Q-020833
1 x 4" Rubber Hose Connection
1 x QZ0280 33.25" Quartz Sleeve
1 x Wiper Nut for Sunlight Systems SL160
1 x LP4020 61.2" Ultraviolet Lamp, 4 Pin Flat
1 x QZ0145 64" Quartz Sleeve
1 x Solberg Small Filter Silencer 3" NPT(M) - FS-230P-300
1 x LP4390 61.2" HO Ultraviolet Lamp, 3-1 Step
1 x Norweco AT1500 UV Lamp
1 x LP4110 14.25" Ozone Ultraviolet Lamp, 4 Pin Flat
$2,644.14
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search